Chiptuning files » BMW » M5 » G90 06/2024 » 4.4 V8 Bi-Turbo PHEV (727 hp / 1000 Nm)

Chiptuning files for BMW M5 G90 06/2024 4.4 V8 Bi-Turbo PHEV (727 hp)

ECU: Bosch MG1CS221

727 HPstock power
1000 Nmstock torque
542 KWstock power

Select a stage for the tuned figures and the power and torque curve.

Available modifications

Deactivations and fixes

What each modification does
Stage 1 for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Software-only remap for a car with standard hardware. 727 hp to 855 hp and 1000 Nm to 1105 Nm.
Stage 2 BASE for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Remap matched to hardware upgrades. Which parts are needed differs per engine. If needed we fine-tune the file up to 3 times free of charge, based on the datalogs you send us. 727 hp to 896 hp and 1000 Nm to 1146 Nm.
Stage 3 BASE for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Remap for a larger or hybrid turbo with supporting hardware. If needed we fine-tune the file up to 3 times free of charge, based on the datalogs you send us. 727 hp to 1034 hp and 1000 Nm to 1238 Nm.
E85 or other special fuels modification for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
The calibration is set up for one special fuel, for example E85. This is not a flex-fuel setup.
Gearbox TCU tuning for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Faster shift times, modified shift points, raised torque limiters, raised rpm limits and higher clutch pressure where needed.
Pops and bangs for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Fuel still injected on overrun ignites in the exhaust and gives the crackle sound. Intensity can be set: soft (burbles), normal, hard or flames.
DTC off for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Selected fault codes are switched off so they are no longer stored or shown.
Cold start off - Catalyst heating off for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
The catalyst-heating phase after a cold start (raised idle, retarded ignition) is removed.
Exhaust flap control/off for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Exhaust valves can be opened or closed independent of the driving mode. For cars with valves in the original exhaust.
Readiness ok for BMW M5 4.4 V8 Bi-Turbo PHEV (727 hp)
Readiness monitors are set so the car reports ready at an emission inspection.

Prices for this vehicle

Prices shown for single credits. Choose a credit pack to see how much cheaper it is; unused credits stay in your account for other projects. Prices for cars. Prices are set in euro.

Tuning filePrice
Stage 180 credits (€112)
Stage 2 BASE90 credits (€126)
Stage 3 BASE250 credits (€350)
Gearbox TCU tuning Stage 1 BASIC75 credits (€105)
Gearbox TCU tuning Stage 199 credits (€138.60)
Gearbox TCU tuning Stage 2 BASE150 credits (€210)
Gearbox TCU tuning Stage 3 BASE195 credits (€273)

Options

OptionOrdered on its ownAdded to a Stage 1 file
E85 or other special fuels modification120 credits (€168)+ 120 credits (€168)
Pops and bangs70 credits (€98)+ 40 credits (€56)
DTC off45 credits (€63)+ 30 credits (€42)
Cold start off - Catalyst heating off50 credits (€70)+ 50 credits (€70)
Exhaust flap control/off55 credits (€77)+ 45 credits (€63)
Readiness ok45 credits (€63)+ 15 credits (€21)

Most options cost less when you add them to a stage file than when you order them on their own.

Tools to read this vehicle

ToolECU read methodTCU read method
AutotunerBench after remote unlock–
PCMflashBoot–
Results vary per vehicle, and what is possible can differ per software version. This applies to every modification we deliver, for the ECU and for the TCU. Upload your original file to check what is available for your vehicle.

BMW M5 4.4 V8 Bi-Turbo PHEV tuning file

ECU and TCU files for the BMW M5 G90 06/2024 4.4 V8 Bi-Turbo PHEV (727 hp).

Stage 1 on average in 50 minutes.

Upload your original file

Prices for this vehicle

Engine and control units

Fuel
Petrol plug-in hybrid
Engine code
S68B44T0
Displacement
4395 cc
Stock power
727 hp / 542 kW
Stock torque
1000 Nm
ECU
Bosch MG1CS221

We walk the extra mile.

Full throttle to the solution

Continuously improving

We regularly make improvements to existing files.

Fast response times

We are easy to reach and respond quickly to all your questions.

Developed on dyno

Many of our tuning files are carefully tested on dyno and road.

We are here to help you

Our engineers are highly skilled and have many years of experience in calibrating engines and gearboxes. They are here to answer your questions.

ECUFILES engineer at work

2512 real customers worldwide

QS RACINGGuosong Huang
★★★★★

I like your team. Because we have cooperated for 4 years.

Ecufiles response: Thanks a lot for your compliment and for already working with us for the last 4 years.

Antonis Markou GarageMarkou Constantinos
★★★★★

I am very happy to meet you guys and I love working with you! Keep going !

Ecufiles response: Dear Antonis, Thanks a lot for your compliments.

All reviews

Technical Questions
For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

Sales Questions
For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

For sales questions, you can also reach us at:

WhatsApp: +31686247602

Response time: Moderate!

WhatsApp