Chiptuning files » Volkswagen » Passat » B6 2006 2010 » 3.6 FSI (280 hp / 360 Nm)

Chiptuning files for Volkswagen Passat B6 2006 2010 3.6 FSI (280 hp)

ECU: Bosch MED9.1.1

280 HPstock power
360 Nmstock torque
209 KWstock power

Select a stage for the tuned figures and the power and torque curve.

Available modifications

Immobiliser and cloning

What each modification does
Stage 1 for Volkswagen Passat 3.6 FSI (280 hp)
Software-only remap for a car with standard hardware. 280 hp to 294 hp and 360 Nm to 379 Nm.
Stage 2 BASE for Volkswagen Passat 3.6 FSI (280 hp)
Remap matched to hardware upgrades. Which parts are needed differs per engine. If needed we fine-tune the file up to 3 times free of charge, based on the datalogs you send us.
Flex fuel mod for E85 or other fuel types for Volkswagen Passat 3.6 FSI (280 hp)
The engine adapts to the fuel that is in the tank, from petrol to E85 and any blend in between. This is not a fixed E85 calibration.
Pops and bangs for Volkswagen Passat 3.6 FSI (280 hp)
Fuel still injected on overrun ignites in the exhaust and gives the crackle sound. Intensity can be set: soft (burbles), normal, hard or flames.
VMAX speedlimit on/off higher/lower for Volkswagen Passat 3.6 FSI (280 hp)
The electronic speed limiter is removed, raised or lowered.
DTC off for Volkswagen Passat 3.6 FSI (280 hp)
Selected fault codes are switched off so they are no longer stored or shown.
Start/Stop System Off for Volkswagen Passat 3.6 FSI (280 hp)
Start-stop is switched off by default.
Cold start off - Catalyst heating off for Volkswagen Passat 3.6 FSI (280 hp)
The catalyst-heating phase after a cold start (raised idle, retarded ignition) is removed.
Catalyst off for Volkswagen Passat 3.6 FSI (280 hp)
Catalyst monitoring by the lambda (O2) sensor is switched off so a sport catalyst or decat does not raise fault codes.
EVAP off for Volkswagen Passat 3.6 FSI (280 hp)
Monitoring of the fuel vapour (EVAP) system is switched off.
SAI off for Volkswagen Passat 3.6 FSI (280 hp)
The secondary air injection system is switched off in software.
IMMO_OFF for Volkswagen Passat 3.6 FSI (280 hp)
The immobiliser check is removed from the ECU, so the engine starts without the immobiliser.
Checksum Correction for Volkswagen Passat 3.6 FSI (280 hp)
The checksums of the file are recalculated so the control unit accepts the modified software.
Idle RPM Mod for Volkswagen Passat 3.6 FSI (280 hp)
The idle speed is raised or lowered; the rev limit can be changed as well.
Anti lag for Volkswagen Passat 3.6 FSI (280 hp)
Boost is kept up when you lift off the throttle, so the turbo responds sooner when you accelerate again.

Prices for this vehicle

Prices shown for single credits. Choose a credit pack to see how much cheaper it is; unused credits stay in your account for other projects. Prices for cars. Prices are set in euro.

Tuning filePrice
Stage 170 credits (€98)
Stage 2 BASE90 credits (€126)

Options

OptionOrdered on its ownAdded to a Stage 1 file
Flex fuel mod for E85 or other fuel types150 credits (€210)+ 150 credits (€210)
Pops and bangs70 credits (€98)+ 40 credits (€56)
VMAX speedlimit on/off higher/lower40 credits (€56)included
DTC off45 credits (€63)+ 30 credits (€42)
Start/Stop System Off40 credits (€56)+ 40 credits (€56)
Cold start off - Catalyst heating off50 credits (€70)+ 50 credits (€70)
Catalyst off40 credits (€56)+ 20 credits (€28)
EVAP off40 credits (€56)+ 40 credits (€56)
SAI off40 credits (€56)+ 40 credits (€56)
IMMO_OFF99 credits (€138.60)+ 99 credits (€138.60)
Checksum Correction10 credits (€14)+ 10 credits (€14)
Idle RPM Mod45 credits (€63)+ 45 credits (€63)

Most options cost less when you add them to a stage file than when you order them on their own.

Tools to read this vehicle

ToolECU read methodTCU read method
Magicmotorsport FLEXBench, Boot, OBD–
Alientech KESS3OBD, Bench, Boot–
Alientech PowergateOBD–
PCMflashBoot–

Also listed for this vehicle: Flashtec CMD, bFlash.

Results vary per vehicle, and what is possible can differ per software version. This applies to every modification we deliver, for the ECU and for the TCU. Upload your original file to check what is available for your vehicle.

Volkswagen Passat 3.6 FSI tuning file

ECU and TCU files for the Volkswagen Passat B6 2006 2010 3.6 FSI (280 hp).

Stage 1 on average in 50 minutes.

Upload your original file

Prices for this vehicle

Engine and control units

Fuel
Petrol
Engine code
BLV
Displacement
3598 cc
Stock power
280 hp / 209 kW
Stock torque
360 Nm
ECU
Bosch MED9.1.1

We walk the extra mile.

Full throttle to the solution

Continuously improving

We regularly make improvements to existing files.

Fast response times

We are easy to reach and respond quickly to all your questions.

Developed on dyno

Many of our tuning files are carefully tested on dyno and road.

We are here to help you

Our engineers are highly skilled and have many years of experience in calibrating engines and gearboxes. They are here to answer your questions.

ECUFILES engineer at work

2512 real customers worldwide

QS RACINGGuosong Huang
★★★★★

I like your team. Because we have cooperated for 4 years.

Ecufiles response: Thanks a lot for your compliment and for already working with us for the last 4 years.

Antonis Markou GarageMarkou Constantinos
★★★★★

I am very happy to meet you guys and I love working with you! Keep going !

Ecufiles response: Dear Antonis, Thanks a lot for your compliments.

All reviews

Technical Questions
For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

Sales Questions
For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

For sales questions, you can also reach us at:

WhatsApp: +31686247602

Response time: Moderate!

WhatsApp