Chiptuning files » Seat » Mii » 2011 2019 » 1.0i CNG (68 hp / 90 Nm)

Chiptuning files for Seat Mii 2011 2019 1.0i CNG (68 hp)

ECU: Bosch ME17.5.20 / Siemens/Continental Simos 11.1

68 HPstock power
90 Nmstock torque
51 KWstock power

Select a stage for the tuned figures and the power and torque curve.

Available modifications

Immobiliser and cloning

What each modification does
Stage 1 for Seat Mii 1.0i CNG (68 hp)
Software-only remap for a car with standard hardware. 68 hp to 78 hp and 90 Nm to 100 Nm.
Stage 2 BASE for Seat Mii 1.0i CNG (68 hp)
Remap matched to hardware upgrades. Which parts are needed differs per engine. If needed we fine-tune the file up to 3 times free of charge, based on the datalogs you send us.
E85 or other special fuels modification for Seat Mii 1.0i CNG (68 hp)
The calibration is set up for one special fuel, for example E85. This is not a flex-fuel setup.
Pops and bangs for Seat Mii 1.0i CNG (68 hp)
Fuel still injected on overrun ignites in the exhaust and gives the crackle sound. Intensity can be set: soft (burbles), normal, hard or flames.
VMAX speedlimit on/off higher/lower for Seat Mii 1.0i CNG (68 hp)
The electronic speed limiter is removed, raised or lowered.
DTC off for Seat Mii 1.0i CNG (68 hp)
Selected fault codes are switched off so they are no longer stored or shown.
Start/Stop System Off for Seat Mii 1.0i CNG (68 hp)
Start-stop is switched off by default.
Cold start off - Catalyst heating off for Seat Mii 1.0i CNG (68 hp)
The catalyst-heating phase after a cold start (raised idle, retarded ignition) is removed.
Catalyst off for Seat Mii 1.0i CNG (68 hp)
Catalyst monitoring by the lambda (O2) sensor is switched off so a sport catalyst or decat does not raise fault codes.
EVAP off for Seat Mii 1.0i CNG (68 hp)
Monitoring of the fuel vapour (EVAP) system is switched off.
SAI off for Seat Mii 1.0i CNG (68 hp)
The secondary air injection system is switched off in software.
Readiness ok for Seat Mii 1.0i CNG (68 hp)
Readiness monitors are set so the car reports ready at an emission inspection.
IMMO_OFF for Seat Mii 1.0i CNG (68 hp)
The immobiliser check is removed from the ECU, so the engine starts without the immobiliser.
Cloning (ECU/TCU) for Seat Mii 1.0i CNG (68 hp)
The complete content of one unit is copied to another unit of the same type.
Checksum Correction for Seat Mii 1.0i CNG (68 hp)
The checksums of the file are recalculated so the control unit accepts the modified software.

Prices for this vehicle

Prices shown for single credits. Choose a credit pack to see how much cheaper it is; unused credits stay in your account for other projects. Prices for cars. Prices are set in euro.

Tuning filePrice
Stage 170 to 80 credits (€98 to €112), by model year
Stage 2 BASE90 credits (€126)

Options

OptionOrdered on its ownAdded to a Stage 1 file
E85 or other special fuels modification120 credits (€168)+ 120 credits (€168)
Pops and bangs70 credits (€98)+ 40 credits (€56)
VMAX speedlimit on/off higher/lower40 credits (€56)included
DTC off45 credits (€63)+ 30 credits (€42)
Start/Stop System Off40 credits (€56)+ 40 credits (€56)
Cold start off - Catalyst heating off50 credits (€70)+ 50 credits (€70)
Catalyst off40 credits (€56)+ 20 credits (€28)
EVAP off40 to 50 credits (€56 to €70), by model year+ 40 credits (€56)
SAI off40 credits (€56)+ 40 credits (€56)
Readiness ok45 credits (€63)+ 15 credits (€21)
IMMO_OFF99 credits (€138.60)+ 99 credits (€138.60)
Cloning (ECU/TCU)199 credits (€278.60)–
Checksum Correction10 credits (€14)+ 10 credits (€14)

Most options cost less when you add them to a stage file than when you order them on their own.

Tools to read this vehicle

ToolECU read methodTCU read method
AutotunerBench, Boot, OBD–
Magicmotorsport FLEXBench, Boot, OBD–
Alientech KESS3Bench, Boot–
Flashtec CMDBench, Boot–
PCMflashOBD, Boot–
Results vary per vehicle, and what is possible can differ per software version. This applies to every modification we deliver, for the ECU and for the TCU. Upload your original file to check what is available for your vehicle.

Seat Mii 1.0i CNG tuning file

ECU and TCU files for the Seat Mii 2011 2019 1.0i CNG (68 hp).

Stage 1 on average in 50 minutes.

Upload your original file

Prices for this vehicle

Engine and control units

Fuel
Petrol
Engine code
CPGA
Stock power
68 hp / 51 kW
Stock torque
90 Nm
ECU
Bosch ME17.5.20, Siemens/Continental Simos 11.1

We walk the extra mile.

Full throttle to the solution

Continuously improving

We regularly make improvements to existing files.

Fast response times

We are easy to reach and respond quickly to all your questions.

Developed on dyno

Many of our tuning files are carefully tested on dyno and road.

We are here to help you

Our engineers are highly skilled and have many years of experience in calibrating engines and gearboxes. They are here to answer your questions.

ECUFILES engineer at work

2512 real customers worldwide

QS RACINGGuosong Huang
★★★★★

I like your team. Because we have cooperated for 4 years.

Ecufiles response: Thanks a lot for your compliment and for already working with us for the last 4 years.

Antonis Markou GarageMarkou Constantinos
★★★★★

I am very happy to meet you guys and I love working with you! Keep going !

Ecufiles response: Dear Antonis, Thanks a lot for your compliments.

All reviews

Technical Questions
For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

Sales Questions
For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

For sales questions, you can also reach us at:

WhatsApp: +31686247602

Response time: Moderate!

WhatsApp