Chiptuning files » Mercedes-Benz » G » 05/2018 2023 » 500 (4.0) (422 hp / 600 Nm)

Chiptuning files for Mercedes-Benz G 05/2018 2023 500 (4.0) (422 hp)

ECU: Bosch MED17.7.5 · TCU: Bosch 9G-Tronic VGS-NAG3

422 HPstock power
600 Nmstock torque
315 KWstock power

Select a stage for the tuned figures and the power and torque curve.

Available modifications

Immobiliser and cloning

What each modification does
Stage 1 for Mercedes-Benz G 500 (4.0) (422 hp)
Software-only remap for a car with standard hardware. 422 hp to 513 hp and 600 Nm to 823 Nm.
E85 or other special fuels modification for Mercedes-Benz G 500 (4.0) (422 hp)
The calibration is set up for one special fuel, for example E85. This is not a flex-fuel setup.
Pops and bangs for Mercedes-Benz G 500 (4.0) (422 hp)
Fuel still injected on overrun ignites in the exhaust and gives the crackle sound. Intensity can be set: soft (burbles), normal, hard or flames.
VMAX speedlimit on/off higher/lower for Mercedes-Benz G 500 (4.0) (422 hp)
The electronic speed limiter is removed, raised or lowered.
DTC off for Mercedes-Benz G 500 (4.0) (422 hp)
Selected fault codes are switched off so they are no longer stored or shown.
Start/Stop System Off for Mercedes-Benz G 500 (4.0) (422 hp)
Start-stop is switched off by default.
Cold start off - Catalyst heating off for Mercedes-Benz G 500 (4.0) (422 hp)
The catalyst-heating phase after a cold start (raised idle, retarded ignition) is removed.
Exhaust flap control/off for Mercedes-Benz G 500 (4.0) (422 hp)
Exhaust valves can be opened or closed independent of the driving mode. For cars with valves in the original exhaust.
Catalyst off for Mercedes-Benz G 500 (4.0) (422 hp)
Catalyst monitoring by the lambda (O2) sensor is switched off so a sport catalyst or decat does not raise fault codes.
DPF/OPF/GPF off for Mercedes-Benz G 500 (4.0) (422 hp)
The particulate filter function (diesel DPF, petrol OPF/GPF) is switched off in software. The filter has to be removed physically first.
EVAP off for Mercedes-Benz G 500 (4.0) (422 hp)
Monitoring of the fuel vapour (EVAP) system is switched off.
SAI off for Mercedes-Benz G 500 (4.0) (422 hp)
The secondary air injection system is switched off in software.
Cylinder On Demand off for Mercedes-Benz G 500 (4.0) (422 hp)
Cylinder deactivation is switched off so the engine always runs on all cylinders.
Torque monitoring off for Mercedes-Benz G 500 (4.0) (422 hp)
Torque monitoring is relaxed so a higher torque does not trigger limp mode.
Readiness ok for Mercedes-Benz G 500 (4.0) (422 hp)
Readiness monitors are set so the car reports ready at an emission inspection.
IMMO_OFF for Mercedes-Benz G 500 (4.0) (422 hp)
The immobiliser check is removed from the ECU, so the engine starts without the immobiliser.
Cloning (ECU/TCU) for Mercedes-Benz G 500 (4.0) (422 hp)
The complete content of one unit is copied to another unit of the same type.

Prices for this vehicle

Prices shown for single credits. Choose a credit pack to see how much cheaper it is; unused credits stay in your account for other projects. Prices for cars. Prices are set in euro.

Tuning filePrice
Stage 180 credits (€112)

Options

OptionOrdered on its ownAdded to a Stage 1 file
E85 or other special fuels modification120 credits (€168)+ 120 credits (€168)
Pops and bangs70 credits (€98)+ 40 credits (€56)
VMAX speedlimit on/off higher/lower40 credits (€56)included
DTC off45 credits (€63)+ 30 credits (€42)
Start/Stop System Off40 credits (€56)+ 40 credits (€56)
Cold start off - Catalyst heating off50 credits (€70)+ 50 credits (€70)
Exhaust flap control/off55 credits (€77)+ 45 credits (€63)
Catalyst off40 credits (€56)+ 20 credits (€28)
DPF/OPF/GPF off50 credits (€70)+ 35 credits (€49)
EVAP off50 credits (€70)+ 40 credits (€56)
SAI off40 credits (€56)+ 40 credits (€56)
Cylinder On Demand off25 credits (€35)+ 25 credits (€35)
Readiness ok45 credits (€63)+ 15 credits (€21)
IMMO_OFF99 credits (€138.60)+ 99 credits (€138.60)
Cloning (ECU/TCU)199 credits (€278.60)–

Most options cost less when you add them to a stage file than when you order them on their own.

Tools to read this vehicle

ToolECU read methodTCU read method
AutotunerBench, Boot, OBDBench, OBD
Flashtec CMDOBD, Bench, BootBench
PCMflashOBD, Boot–

Also listed for this vehicle: Alientech KESS3, Dimsport New Genius, Dimsport New Trasdata.

Results vary per vehicle, and what is possible can differ per software version. This applies to every modification we deliver, for the ECU and for the TCU. Upload your original file to check what is available for your vehicle.

Mercedes-Benz G 500 (4.0) tuning file

ECU and TCU files for the Mercedes-Benz G 05/2018 2023 500 (4.0) (422 hp).

Stage 1 on average in 50 minutes.

Upload your original file

Prices for this vehicle

Engine and control units

Fuel
Petrol
Engine code
M176
Displacement
3982 cc
Stock power
422 hp / 315 kW
Stock torque
600 Nm
ECU
Bosch MED17.7.5
TCU
Bosch 9G-Tronic VGS-NAG3

We walk the extra mile.

Full throttle to the solution

Continuously improving

We regularly make improvements to existing files.

Fast response times

We are easy to reach and respond quickly to all your questions.

Developed on dyno

Many of our tuning files are carefully tested on dyno and road.

We are here to help you

Our engineers are highly skilled and have many years of experience in calibrating engines and gearboxes. They are here to answer your questions.

ECUFILES engineer at work

2512 real customers worldwide

QS RACINGGuosong Huang
★★★★★

I like your team. Because we have cooperated for 4 years.

Ecufiles response: Thanks a lot for your compliment and for already working with us for the last 4 years.

Antonis Markou GarageMarkou Constantinos
★★★★★

I am very happy to meet you guys and I love working with you! Keep going !

Ecufiles response: Dear Antonis, Thanks a lot for your compliments.

All reviews

Technical Questions
For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

Sales Questions
For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

For sales questions, you can also reach us at:

WhatsApp: +31686247602

Response time: Moderate!

WhatsApp