Chiptuning files » Bentley » Mulsanne » until 2016 » 6.75 V8 Bi-Turbo (537 hp / 1100 Nm)

Chiptuning files for Bentley Mulsanne until 2016 6.75 V8 Bi-Turbo (537 hp)

ECU: Bosch ME17.1.1 / Bosch MED17.1.1 · TCU: ZF AL951

537 HPstock power
1100 Nmstock torque
400 KWstock power

Select a stage for the tuned figures and the power and torque curve.

Available modifications

Immobiliser and cloning

What each modification does
Stage 1 for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Software-only remap for a car with standard hardware. 537 hp to 648 hp and 1100 Nm to 1298 Nm.
Stage 2 BASE for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Remap matched to hardware upgrades. Which parts are needed differs per engine. If needed we fine-tune the file up to 3 times free of charge, based on the datalogs you send us.
E85 or other special fuels modification for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The calibration is set up for one special fuel, for example E85. This is not a flex-fuel setup.
Flex fuel mod for E85 or other fuel types for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The engine adapts to the fuel that is in the tank, from petrol to E85 and any blend in between. This is not a fixed E85 calibration.
Pops and bangs for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Fuel still injected on overrun ignites in the exhaust and gives the crackle sound. Intensity can be set: soft (burbles), normal, hard or flames.
VMAX speedlimit on/off higher/lower for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The electronic speed limiter is removed, raised or lowered.
DTC off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Selected fault codes are switched off so they are no longer stored or shown.
Cold start off - Catalyst heating off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The catalyst-heating phase after a cold start (raised idle, retarded ignition) is removed.
Exhaust flap control/off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Exhaust valves can be opened or closed independent of the driving mode. For cars with valves in the original exhaust.
Catalyst off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Catalyst monitoring by the lambda (O2) sensor is switched off so a sport catalyst or decat does not raise fault codes.
EVAP off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Monitoring of the fuel vapour (EVAP) system is switched off.
SAI off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The secondary air injection system is switched off in software.
Cylinder On Demand off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Cylinder deactivation is switched off so the engine always runs on all cylinders.
Torque monitoring off for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Torque monitoring is relaxed so a higher torque does not trigger limp mode.
Readiness ok for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Readiness monitors are set so the car reports ready at an emission inspection.
Boost Sensor Calibration for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
Calibration for an uprated boost pressure (MAP) sensor.
RPM Limit Mod for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The engine speed limit is raised or lowered.
IMMO_OFF for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The immobiliser check is removed from the ECU, so the engine starts without the immobiliser.
Cloning (ECU/TCU) for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The complete content of one unit is copied to another unit of the same type.
Checksum Correction for Bentley Mulsanne 6.75 V8 Bi-Turbo (537 hp)
The checksums of the file are recalculated so the control unit accepts the modified software.

Prices for this vehicle

Prices shown for single credits. Choose a credit pack to see how much cheaper it is; unused credits stay in your account for other projects. Prices for cars. Prices are set in euro.

Tuning filePrice
Stage 160 to 80 credits (€84 to €112), by model year
Stage 2 BASE90 credits (€126)

Options

OptionOrdered on its ownAdded to a Stage 1 file
E85 or other special fuels modification120 credits (€168)+ 120 credits (€168)
Flex fuel mod for E85 or other fuel types150 credits (€210)+ 150 credits (€210)
Pops and bangs70 credits (€98)+ 40 credits (€56)
VMAX speedlimit on/off higher/lower40 credits (€56)included
DTC off45 credits (€63)+ 30 credits (€42)
Cold start off - Catalyst heating off50 credits (€70)+ 50 credits (€70)
Exhaust flap control/off45 to 55 credits (€63 to €77), by model year+ 45 credits (€63)
Catalyst off40 credits (€56)+ 20 credits (€28)
EVAP off40 to 50 credits (€56 to €70), by model year+ 40 credits (€56)
SAI off40 credits (€56)+ 40 credits (€56)
Cylinder On Demand off25 credits (€35)+ 25 credits (€35)
Readiness ok45 credits (€63)+ 15 credits (€21)
Boost Sensor Calibration55 to 65 credits (€77 to €91), by model year+ 55 credits (€77)
RPM Limit Mod35 to 45 credits (€49 to €63), by model yearincluded
IMMO_OFF99 credits (€138.60)+ 99 credits (€138.60)
Cloning (ECU/TCU)199 credits (€278.60)–
Checksum Correction10 credits (€14)+ 10 credits (€14)

Most options cost less when you add them to a stage file than when you order them on their own.

Tools to read this vehicle

ToolECU read methodTCU read method
Magicmotorsport FLEXBench, Boot, OBDBench, OBD
Alientech KESS3Bench, Boot–
Flashtec CMDOBD, Bench, BootOBD
PCMflashBoot–
Results vary per vehicle, and what is possible can differ per software version. This applies to every modification we deliver, for the ECU and for the TCU. Upload your original file to check what is available for your vehicle.

Bentley Mulsanne 6.75 V8 Bi-Turbo tuning file

ECU and TCU files for the Bentley Mulsanne until 2016 6.75 V8 Bi-Turbo (537 hp).

Stage 1 on average in 50 minutes.

Upload your original file

Prices for this vehicle

Engine and control units

Fuel
Petrol
Engine code
CZMA / CKB
Displacement
6752 cc
Stock power
537 hp / 400 kW
Stock torque
1100 Nm
ECU
Bosch ME17.1.1, Bosch MED17.1.1
TCU
ZF AL951

We walk the extra mile.

Full throttle to the solution

Continuously improving

We regularly make improvements to existing files.

Fast response times

We are easy to reach and respond quickly to all your questions.

Developed on dyno

Many of our tuning files are carefully tested on dyno and road.

We are here to help you

Our engineers are highly skilled and have many years of experience in calibrating engines and gearboxes. They are here to answer your questions.

ECUFILES engineer at work

2512 real customers worldwide

QS RACINGGuosong Huang
★★★★★

I like your team. Because we have cooperated for 4 years.

Ecufiles response: Thanks a lot for your compliment and for already working with us for the last 4 years.

Antonis Markou GarageMarkou Constantinos
★★★★★

I am very happy to meet you guys and I love working with you! Keep going !

Ecufiles response: Dear Antonis, Thanks a lot for your compliments.

All reviews

Technical Questions
For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

Sales Questions
For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

Response time: Quick!

For sales questions, you can also reach us at:

WhatsApp: +31686247602

Response time: Moderate!

WhatsApp