Technical Description of OBD-II Trouble Code
The circuit controlling the deactivation/intake valve of cylinder 10 is open.
What does that mean?
This is a generic powertrain diagnostic trouble code (DTC) that applies to many OBD-II vehicles (1996-newer), including vehicles from General Motors, Dodge, Jeep, Chevrolet, Chrysler, Ram, etc. The exact repair steps may vary depending on the year, make, model, and powertrain configuration.
OBD-II trouble code P3473 and related codes P3474, P3475, and P3476 are associated with the circuit controlling the deactivation/intake valve of cylinder #10.
The purpose of the circuit controlling the deactivation/intake valve of cylinder 10 is to enable the cylinder deactivation feature (e.g., V4 mode of a V8 engine) to improve fuel economy during light load operation, such as highway driving. The Engine Control Module (ECM) controls the engine’s 4 or 8 cylinder modes by engaging the intake deactivating solenoids for four of the engine cylinders. This code specifically pertains to the number 10 cylinder, while the other three cylinders involved in this process are determined by the engine configuration and firing order. The number one cylinder deactivation solenoid is mounted on or near the intake in the vicinity of that cylinder, depending on the specific vehicle and configuration.
When the ECM detects improper voltage or resistance within the circuit controlling the deactivation/intake valve of cylinder 10, it sets code P3473 and may illuminate the check engine light, service engine soon light, or both. In some cases, the ECM may disable the injector to the #10 cylinder until the issue is resolved and the code is cleared, resulting in a noticeable engine misfire.
Cylinder deactivation solenoids:
What is the severity of this DTC?
The severity of this code can range from moderate to severe, depending on the specific symptoms of the malfunction. A misfire should be addressed immediately, as it can cause permanent damage to internal engine components.
What are some of the symptoms of the code?
Symptoms of a P3473 trouble code may include:
What are some of the common causes of the code?
Causes for this P3473 code may include:
What are some P3473 troubleshooting steps?
The first step in troubleshooting any malfunction is to research the Technical Service Bulletins (TSB’s) for the specific vehicle based on the year, model, and engine. This can save time by providing guidance in the right direction.
The second step is to check the engine oil level and ensure it is at the appropriate level. Then, inspect all components associated with the circuit controlling the deactivation/intake valve of cylinder 10 for any visible physical damage. Depending on the specific vehicle, this circuit may include several components, such as the deactivation solenoid, switches, fault indicators, and the ECM. Conduct a thorough visual inspection of the associated wiring for any obvious defects, such as scraping, rubbing, bare wires, or burn spots. Next, check the connectors and connections for security, corrosion, and damaged pins. This inspection should encompass all wiring connectors and connections to all components, including the ECM. Consult the specific technical data for the vehicle to verify the configuration of the circuit controlling the deactivation/intake valve of cylinder 10 and confirm every component incorporated within the circuit, which may include a fuse or a fuse-able link.
Advanced Steps
The advanced steps are highly specific to the vehicle and require advanced equipment for accurate execution. These procedures necessitate a digital multimeter and the specific technical references for the vehicle.
Voltage Checks
The reference voltage and acceptable ranges may vary based on the specific vehicle and circuit configuration. The troubleshooting charts and appropriate sequence provided in the specific technical data will assist in an accurate diagnosis.
If this process reveals the absence of a power source or ground, continuity testing may be necessary to check the integrity of the wiring, connectors, and other components. Continuity tests should always be performed with the power removed from the circuit, and the normal readings for wiring and connections should be 0 ohms of resistance. Resistance or lack of continuity indicates faulty wiring that is open, shorted, or corroded and must be repaired or replaced.
What are some common repairs for this code?
Common Mistake
We always recommend seeking professional mechanical service to address this issue. However, if that is not possible, we offer the option to permanently delete this specific DTC. All other codes will continue to be addressed. If you are interested in this option, please upload your ECU file to our portal.
