Technical Description of OBD-II Trouble Code
Range/Performance Issue with NOx Sensor Heater Sense Circuit in Bank 2
What does that signify?
This is a standard diagnostic trouble code (DTC) for powertrain issues and is commonly found in OBD-II vehicles. It can be applicable to various vehicle makes such as Mercedes-Benz, Sprinter, VW, Audi, Ford, Dodge, Ram, Jeep, etc.
NOx (Oxides of Nitrogen) sensors are primarily used in diesel engines for emission control. They detect the levels of NOx in the exhaust after combustion in the engine’s combustion chamber. The system then recycles these emissions using different methods. Due to the harsh conditions they operate in, these sensors are made of a combination of ceramic and a specific type of zirconia.
One of the negative impacts of releasing NOx into the atmosphere is the potential for smog and acid rain. Failing to monitor and regulate NOx levels properly can have a significant effect on the environment and the air we breathe. The Engine Control Module (ECM) continuously monitors the NOx sensors to ensure that the emissions from the vehicle’s exhaust are within acceptable limits.
The ECM calculates the levels of Nitric Oxide and Nitrogen Dioxide gases (NOx) by using data from the upstream and downstream oxygen sensors, along with the readings from the NOx sensor. This is done to control the NOx emissions from the vehicle’s tailpipe for environmental reasons. The “Bank 2” mentioned in the trouble codes refers to the engine bank that does not contain the #1 cylinder.
P2222 is the specific code for “NOx Sensor Heater Sense Circuit Range/Performance Bank 2”. This trouble code indicates that the ECM has detected an out-of-range condition with the NOx sensor’s heater sense circuit. In other words, something is causing the sensor to operate outside of the desired electrical range.
It is important to note that diesel engines generate a significant amount of heat, so it is crucial to allow the system to cool down before working on any exhaust system components.
Here is an example of a NOx sensor (in this case, for GM vehicles):
What is the severity of this DTC?
If the trouble codes are ignored and no action is taken to repair them, it could lead to catalytic converter failure. Neglecting the symptoms and causes of these trouble codes can result in further complications for your vehicle, such as frequent stalling and reduced fuel economy. If you notice any of the potential symptoms listed below, it is highly recommended to have your vehicle checked by a professional.
What are some of the symptoms of the code?
Symptoms of a P2222 diagnostic code may include:
What are some of the common causes of the code?
Possible causes for the P2222 NOx sensor code may include:
What are some diagnostic and troubleshooting steps for P2222?
The first step in troubleshooting any malfunction is to research the Technical Service Bulletins (TSB) for known issues with your specific vehicle.
Advanced diagnostic steps are highly vehicle-specific and may require specialized equipment and knowledge for accurate performance. The basic steps provided below should be followed, but refer to a vehicle year/make/model/powertrain specific repair guide for detailed instructions.
Basic Step #1
Always start by clearing the codes and rescanning the vehicle. If none of the Diagnostic Trouble Codes (DTCs) appear as active immediately, take the vehicle for an extended multi-stop test drive to see if they reappear. If only one of the codes is reactivated by the ECM, continue the diagnostic process for that specific code.
Basic Step #2
Next, inspect the exhaust system for any leaks. Black soot around cracks and/or gaskets in the system is a sign of a leak. Address any leaks accordingly. In most cases, replacing an exhaust gasket is a relatively simple task. A fully sealed exhaust system is crucial for the proper functioning of the sensors involved in the exhaust system.
Basic Step #3
Using an infrared temperature gun, monitor the temperature of the exhaust before and after the catalytic converter. Compare the results to the manufacturer’s specifications. Refer to the specific service manual for this information.
Basic Step #4
If the temperature of the catalytic converter is within the specified range, focus on the electrical system related to these sensors. Start with the harness and connector of the bank 2 NOx sensor. These harnesses often crack and fail due to their proximity to the extreme temperatures of the exhaust. Repair any damaged wires by soldering the connections and using heat shrink tubing. Also, inspect the oxygen sensors involved in bank 2 to ensure they are not damaged, as this can affect the downstream NOx readings. Repair any connectors that are not making sufficient connections or are not locking properly.
This article is intended for informational purposes only, and the technical data and service bulletins specific to your vehicle should always take precedence.
