Technical Description of OBD-II Trouble Code
Circuit for Ignition/Distributor Engine Speed Input
What is the meaning of this?
This generic diagnostic trouble code for powertrain/engine typically applies to all spark ignition engines, including certain Ford, Kia, Mazda, and Mercedes vehicles.
The Powertrain Control Module or PCM receives crankshaft position or crankshaft timing information from the Crankshaft Position Sensor (CKP). This information is usually used for engine rpm. The PCM also receives camshaft position information from the camshaft position sensor (CMP), which provides the exact location of the camshaft, camshaft timing, or distributor timing.
When there is an electrical problem with either of these two circuits, the PCM will set code P0320, depending on how the manufacturer wants to identify the fault. This code is specifically related to an electrical circuit fault.
The troubleshooting steps may vary depending on the manufacturer, type of ignition/distributor/engine speed sensor, and wire colors to the sensor.
Symptoms
The symptoms of a P0320 engine code may include:
Causes
The potential causes for this code to set are:
Diagnostic and Repair Procedures
A good starting point is always to check for technical service bulletins (TSB) for your particular vehicle. Your issue may be a known issue with a known fix provided by the manufacturer, which can save you time and money during diagnosis.
Next, locate the ignition/distributor/engine speed sensor on your particular vehicle. This may be a crank sensor/cam sensor; it might be a pick up coil/sensor inside the distributor; it may even be a wire coming from the coil going to the PCM to verify ignition system firing. Once located, visually inspect the connectors and wiring. Look for scraping, rubbing, bare wires, burn spots, or melted plastic. Pull the connectors apart and carefully inspect the terminals (the metal parts) inside the connectors. See if they look burned or have a green tint indicating corrosion. Use electrical contact cleaner and a plastic bristle brush if cleaning of the terminals is needed. Let dry and apply electrical grease where the terminals contact.
Depending on the vehicle, the most likely cause for the P0320 code to set is poor connections/updated ignition parts. Therefore, conducting a TSB search on your vehicle is highly recommended.
If you have a scan tool, clear the diagnostic trouble codes from memory and see if P0320 returns. If it does not, then the connections were most likely the problem.
If the P0320 code does return, we will need to test the sensor and its associated circuits. The next steps will depend on the type of sensor you have: Hall Effect or Magnetic Pick up. You can usually determine which one you have by the number of wires coming from the sensor. If there are 3 wires from the sensor, it is a Hall Effect sensor. If it has 2 wires, it will be a Magnetic Pick up style sensor.
If it is a Hall Effect sensor, disconnect the harness going to the Camshaft and the Crankshaft Position Sensors. With a Digital Volt Ohm Meter (DVOM), test the 5V power supply circuit going to each sensor to ensure it is receiving power (Red lead to the 5V power supply circuit, black lead to a good ground). If there is no 5 volts to the sensor, repair the wiring from the PCM to the sensor, or possibly replace the PCM.
If thatâs OK, with a DVOM, check to make sure you have 5V on each signal circuit going to each sensor to ensure it has a signal circuit (Red lead to the sensor signal circuit, black lead to a good ground). If there is no 5 volts to the sensor, repair the wiring from the PCM to the sensor, or possibly replace the PCM.
If thatâs OK, check to make sure you have a good ground at each sensor. Connect a test light to 12V and touch the other end of the test light to the ground circuit going to each sensor. If the test light does not light up, this would indicate a problem with the circuit. If it does light up, wiggle the wiring harness going to each sensor to see if the test light flickers, indicating an intermittent connection.
If it is a Magnetic Pickup style sensor, we can check the sensor itself to see if it is working properly. We will test it for: 1) Resistance 2) A/C voltage output 3) Short to ground
With the sensor disconnected, connect the two leads of your ohmmeter to the 2 terminals of the Camshaft / Crankshaft Position Sensor. Read the ohms resistance and compare it to the specifications for your vehicle, typically 750 â 2000 ohms. While still on ohms, disconnect 1 lead of your ohmmeter from the sensor and connect it to a good ground on the vehicle. If you get any ohms reading other than infinite or OL, the sensor has an internal short to ground. Remember not to touch the metal part of the leads with your fingers, as this may affect your readings.
Reconnect the two leads of your DVOM to the 2 terminals of the Camshaft / Crankshaft Position Sensor. Set your meter to read A/C voltage. While cranking the engine over, read the a/c voltage output on your DVOM. Compare it to the manufacturers specifications for your vehicle. A good rule of thumb is generally .5V AC.
If all tests have passed so far, and you continue to get a P0320 code, this would most likely indicate a failed ignition/distributor/engine speed sensor, although a failed PCM cannot be ruled out until the sensor has been replaced. In some instances, once the sensor has been replaced, it will need to be calibrated to the PCM in order to function properly.
If you are unsure, seek assistance from a trained automotive diagnostician. PCMs must be programmed or calibrated to the vehicle in order to be installed correctly.
