Technical Description of OBD-II Trouble Code
Restricted Fuel Injector in Cylinder 6
What does that signify?
This is a generic diagnostic trouble code (DTC) that applies to OBD-II vehicles. It can be found in various vehicles including Ford (Transit, Focus, etc), Land Rover, Mitsubishi, Maybach, Dodge, Subaru, etc. Although it is a generic code, the specific repair steps may vary depending on the year, make, model, and powertrain configuration of the vehicle.
If your OBD-II equipped vehicle has stored the code P02B0, it means that the powertrain control module (PCM) has detected a possible restriction in the fuel injector for cylinder #6 of the engine.
Automotive fuel injectors need to maintain a precise fuel pressure in order to deliver the correct amount of fuel in a precise spray pattern to each cylinder’s combustion chamber. To achieve this precision, fuel injectors must be free of leaks and restrictions.
The PCM monitors factors such as fuel trim requirements, exhaust oxygen sensor data, crankshaft position, and camshaft position to detect a lean condition and identify the specific cylinder experiencing a malfunction. Oxygen sensor data informs the PCM about lean exhaust oxygen content and which bank of the engine is affected. By analyzing the position of the camshaft and crankshaft, the PCM can determine which fuel injector is causing the problem. Once the PCM identifies a lean condition and locates the affected fuel injector in cylinder #6, it stores the code P02B0 and may illuminate the malfunction indicator lamp (MIL).
In some cases, multiple failure cycles may be required for the MIL to illuminate.
A cross section of a typical fuel injector:
What is the severity of this DTC?
A P02B0 code should be considered severe because a lean fuel condition could potentially cause damage to the cylinder head or engine.
What are some of the symptoms of the code?
Symptoms of a P02B0 trouble code may include:
What are some of the common causes of the code?
Possible causes for the P02B0 fuel injector code include:
What are some P02B0 troubleshooting steps?
Prior to diagnosing a code P02B0, it is recommended to diagnose and repair any MAF and MAP related codes.
Begin the diagnosis by inspecting the fuel injection rail area. Pay close attention to the fuel injector in question (cylinder #6). Look for signs of corrosion or leakage on the exterior. If heavy corrosion or leakage is present, it is likely that the fuel injector has failed.
If no obvious mechanical issues are found in the engine bay, you will need several tools for an accurate diagnosis:
Next, connect the scanner to the vehicle’s diagnostic port and retrieve all stored codes and freeze frame data. This information will be helpful during the diagnosis. Clear the codes and test-drive the vehicle to see if the P02B0 code reappears.
If the P02B0 code immediately returns, use the scanner to perform an injector balance test to confirm that the misfire is caused by an injector problem. Once this is confirmed, proceed to step 1.
Step 1
With the engine running, use the stethoscope to listen to the fuel injector in question. You should hear a repeated clicking sound in a specific pattern. If there is no sound at all, proceed to step 2. If the sound is strained or intermittent, suspect that the injector for cylinder #6 has failed or is clogged. If needed, compare the sounds from that cylinder’s injector to others for comparison.
Step 2
Use the DVOM to test for voltage and a ground pulse while the engine is running. Most manufacturers use a system where one terminal of the fuel injector receives constant battery voltage, while the other terminal receives a ground pulse from the PCM at the appropriate time.
If there is no voltage at the connector of the fuel injector in question, use the DVOM to test the system fuses and relays. Replace any blown fuses or faulty relays as necessary.
When testing system fuses, it is recommended to test them under a load. A fuse that appears to be good when the circuit is not loaded (key on/engine off) may fail when the circuit is loaded (key on/engine running).
If all system fuses and relays are functioning properly and there is still no voltage, use the vehicle information source to trace the circuit back to the ignition switch or fuel injection module (if applicable).
Note: Exercise caution when testing or replacing high-pressure fuel system components.
