P012C Turbocharger/Supercharger Inlet Pressure Sensor Circuit Low (Downstream of throttle valve)

Technical Description of OBD-II Trouble Code

The circuit for the Turbocharger/Supercharger Inlet Pressure Sensor is experiencing low pressure downstream of the throttle valve.

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code that applies to OBD-II equipped vehicles with a turbocharger or supercharger inlet pressure sensor. This code can be found in various vehicle brands such as Ford, Dodge, Saturn, Nissan, Subaru, Honda, etc. While the code is generic, the specific repair steps may vary depending on the make, model, and engine of the vehicle.

The P012C code indicates a low condition within the Turbo/Supercharger Inlet Pressure Sensor (TCIP) circuit. The turbo/supercharger is responsible for increasing the amount of air (volumetric efficiency) within the combustion chamber by creating pressure in the intake system.

Turbochargers are typically exhaust driven, while superchargers are belt driven. The inlet of the turbo/supercharger is where they draw filtered air from the air filter. The inlet sensor works with the ECM (Electronic Control Module) or PCM (Powertrain Control Module) to monitor and regulate intake pressure.

The “(Downstream of throttle valve)” indicates the specific inlet sensor that is malfunctioning and its location. The pressure sensor may also include a temperature sensor.

This trouble code is closely related to P012A, P012B, P012D, and P012E.

What are some of the symptoms of the code?

Symptoms of a P012C engine code may include:

  • Vehicle entering limp mode (Fail safe mode)
  • Engine noises
  • Poor performance
  • Engine misfiring
  • Stalling
  • Poor fuel mileage
  • What are some of the common causes of the code?

    Causes for this code may include:

  • Defective Turbo/supercharger inlet pressure sensor
  • Broken or damaged wiring harness
  • Problem within general electrical system
  • ECM issue
  • Pin/connector problem. (i.e. corrosion, overheating etc.)
  • Clogged or damaged air filter
  • What are some of the troubleshooting steps?

    It is recommended to check for technical service bulletins (TSBs) for your vehicle. For example, there is a known issue with some Ford / F150 EcoBoost engines, and accessing a known fix can save time and money during diagnosis.

    Tools

    When working with electrical systems, it is advisable to have the following basic tools:

  • OBD code reader
  • Multimeter
  • Basic socket set
  • Basic ratchet and wrench sets
  • Basic screwdriver set
  • Rag/shop towels
  • Battery terminal cleaner
  • Service manual
  • Safety Tips

  • Allow the engine to cool
  • Chalk the wheels
  • Wear PPE (Personal protective equipment)
  • Basic Step #1

    Visually inspect the TCIP and its surroundings. Given the nature of these codes, it is highly likely that there is a physical problem causing the issue. Check the harness thoroughly, as the harness for these sensors typically runs along areas with extremely high temperatures. To locate which sensor’s circuit is malfunctioning, refer to “Downstream of Throttle valve”. Downstream refers to after the throttle valve or the side closer to the intake manifold. The throttle valve is typically mounted to the intake manifold itself. Once the TCIP is located, follow the wires coming out of it and inspect for any frayed, chafed, or cut wires that may be causing an issue. If you have enough access to the sensor’s connector, you can disconnect it and inspect the pins for corrosion.

    NOTE: The presence of green color indicates corrosion. Visually inspect all ground straps and look for corroded or loose ground connections. A problem within the general electrical system can cause drivability issues, poor mileage, and other unrelated problems.

    Basic Step #2

    Depending on the make and model of your vehicle, there may be a fuse box. Fuse boxes can be located in various places such as under the dash, behind the glove box, under the hood, or under a seat. Locate the fuse and ensure that it fits tightly within the slot and is not blown.

    Basic Tip #3

    Check your air filter! Visually inspect the air filter for signs of clogging or dirtiness. A clogged filter may cause a low pressure condition. If the air filter is clogged or showing any signs of damage (e.g., water intrusion), it should be replaced. This is a cost-efficient way to rule out this possibility, as air filters are often inexpensive and easy to replace.

    NOTE: Check if your air filter is cleanable. If so, you may be able to clean it instead of replacing the entire assembly.

    Basic Step #4

    If everything checks out at this point and you still cannot find a malfunction, verify the circuit itself. This may involve disconnecting the ECM or PCM electrical connector, so ensure that your battery is connected. Perform basic electrical tests on the circuit (e.g., check for continuity, check for short to ground, check power, etc.). Any open or short indicates a problem that will need to be repaired. Good luck!

    Professional Service Options

    When facing p012c error, you have two solutions:

    Option 1: Mechanical Repair (Recommended)

    We highly recommend solving this issue by repairing or replacing the faulty sensor, wiring, or related mechanical parts.
    This ensures your vehicle operates as designed.

    Option 2: Permanent p012c DTC Deletion (Alternative)

    If mechanical repair is not possible, we offer a professional service to permanently delete p012c trouble code (DTC) from your ECU.

    Instantly Fix Your DTC Problem – No Hardware Changes Needed!

    Get your p012c code permanently deleted by our experts.

    ✅ Fast. ✅ Reliable. ✅ Keeps your vehicle running smoothly.

    🔥 Upload your ECU file and start now! 🔥

    Already a member? Log in here to submit your file!

    Tuning Files Service from ECUFILES

    Custom Tuning File Service

    EVC Reseller Database

    Automatic File Service

    Technical Questions
    For technical questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

    Response time: Quick!

    Sales Questions
    For sales questions, please register for free and submit a ticket on our platform. One of our engineers will respond to you as soon as possible during business hours.

    Response time: Quick!

    For sales questions, you can also reach us at:

    WhatsApp: +31686247602

    Response time: Moderate!

    WhatsApp