Technical Description of OBD-II Trouble Code
Heater Resistance of HO2S (Bank 2 Sensor 2)
What does that signify?
This diagnostic trouble code (DTC) is a generic powertrain code that is applicable to all vehicles manufactured from 1996 onwards (Chevrolet, Ford, GMC, Mazda, Pontiac, Isuzu, etc.). While it is a generic code, the specific repair steps may vary depending on the make and model of the vehicle.
If your vehicle equipped with OBD-II has stored a code P0060, it indicates that the powertrain control module (PCM) has detected a malfunction in the heater circuit of the downstream oxygen (O2) sensor for engine bank one (or pre catalytic converter). Bank 2 refers to the engine bank that does not contain cylinder #1. Sensor 2 indicates that the issue is related to the downstream sensor.
The O2 sensor consists of a zirconium dioxide sensing element protected by a vented steel housing. Platinum electrodes are used to connect the sensing element to wire leads in the O2 sensor wiring harness. The PCM receives data from the O2 sensor through the controller area network (CAN). This data includes the percentage of oxygen particles in the engine exhaust compared to the oxygen content of ambient air. The PCM utilizes this data to calculate fuel delivery and ignition timing.
The heated O2 sensor uses battery voltage to preheat during cold start conditions. In the heated O2 sensor, there are separate circuits for the O2 sensor signal and the sensor heater. The heater circuit typically carries battery voltage and may have an in-line fuse. When the engine coolant temperature is low, the PCM ensures that battery voltage is applied to the O2 sensor heater until the engine reaches normal operating temperature and enters closed loop operation. The voltage is usually routed through the PCM, sometimes with the assistance of a relay and/or fuses, and is initiated when the ignition switch is turned on during cold start conditions. The PCM is programmed to discontinue battery voltage to the O2 heater circuit once the engine reaches normal operating temperature.
If the PCM detects a level of resistance in the O2 sensor heater circuit that exceeds the programmed limitations, it will store a code P0060 and illuminate the malfunction indicator lamp (MIL). In certain models, the MIL may only be illuminated after multiple ignition cycles with a failure. Therefore, you will need to use the OBD-II readiness mode to ensure the success of your repairs. After performing the repairs, drive the vehicle until the PCM enters readiness mode or the code is reset.
Severity & Symptoms
A code P0060 should be considered severe as it indicates that the upstream O2 sensor heater is not functioning. Symptoms of this engine code may include:
Causes
Possible causes of a P0060 trouble code may include:
Possible Solutions
A good starting point is to check for technical service bulletins (TSB) specific to your vehicle. There may be a known issue with a known fix provided by the manufacturer, which can save you time and money during diagnosis.
When diagnosing a code P0060, you will need a diagnostic scanner, a digital volt ohmmeter (DVOM), and a reliable source of vehicle information, such as All Data DIY.
Begin by visually inspecting the system wiring harnesses and connectors, paying attention to those near hot exhaust pipes and manifolds, as well as those near sharp edges like those found on exhaust shields.
Proceed to test all system fuses and fusible links using the DVOM. Test these components under load, as fuses that appear operational when not loaded may fail when loaded. Activating the O2 sensor heaters will effectively load this circuit.
Retrieve all stored trouble codes and freeze frame data by connecting the scanner to the vehicle diagnostic port. It is helpful to write down this information, especially if the P0060 code proves to be intermittent. Clear the codes and test drive the vehicle to see if the P0060 is immediately reset.
If the code is reset, ensure that the engine is cold enough to activate the O2 sensor heater. Observe O2 sensor heater input data using the scanner data stream, narrowing the display to include only relevant data for faster response. With the engine within the correct temperature range, the O2 sensor heater voltage should be virtually the same as the battery voltage. If the O2 sensor heater voltage deviates from the battery voltage due to a resistance issue, a P0060 code will be stored.
To monitor live data from the O2 sensor heater circuit, connect the DVOM test leads to the sensor ground and battery voltage signal wires. The resistance of the O2 sensor in question can also be checked using the DVOM. Disconnect all related controllers before testing the system circuit resistance with the DVOM.
Additional diagnostic tips & notes:
