Technical Description of OBD-II Trouble Code
Low Sense Circuit for NOx Sensor Heater in Bank 2
What does that signify?
This is a standard diagnostic trouble code (DTC) for powertrain issues and is commonly found in OBD-II vehicles. It can be applicable to various vehicle makes such as Mercedes-Benz, Sprinter, VW, Audi, Ford, Dodge, Ram, Jeep, etc.
NOx (Oxides of Nitrogen) sensors are primarily used in diesel engines for emission control. They detect the levels of NOx in the exhaust after combustion in the engine’s combustion chamber. The system then recycles these emissions using different methods. Due to the harsh environment, these sensors are made of a combination of ceramic and a specific type of zirconia.
One of the negative impacts of releasing NOx into the atmosphere is the potential for smog and acid rain. Failing to monitor and adjust NOx levels properly can have a significant effect on the environment and the air we breathe. The Engine Control Module (ECM) continuously monitors the NOx sensors to ensure that the vehicle’s exhaust emissions are within acceptable limits.
The ECM calculates the levels of Nitric Oxide and Nitrogen Dioxide gases (NOx) by analyzing data from the upstream and downstream oxygen sensors, along with the NOx sensor readings. This is done to regulate the NOx levels emitted from the vehicle’s tailpipe for environmental reasons. The “Bank 2” mentioned in the trouble code refers to the engine bank that does not contain the #1 cylinder.
P2223 is the specific code for “Low Sense Circuit for NOx Sensor Heater in Bank 2”. This code appears when the ECM detects an issue with the output level from this circuit. The readings from the circuit are too low compared to the desired specifications.
It is important to allow the exhaust system components to cool before working on them, especially in diesel engines that generate significant heat.
An example of a NOx sensor (for GM vehicles) is shown below:
What is the severity of this DTC?
If the trouble codes are ignored and no action is taken to repair them, it could lead to catalytic converter failure. Neglecting the symptoms and causes of these trouble codes can result in further complications for the vehicle, such as frequent stalling and reduced fuel economy. If you notice any of the potential symptoms listed below, it is highly recommended to have the vehicle checked by a professional.
What are some of the symptoms of the code?
Symptoms of a P2223 diagnostic code may include:
What are some of the common causes of the code?
Possible causes for the P2223 NOx sensor code may include:
What are some diagnostic and troubleshooting steps for P2223?
The first step in troubleshooting any malfunction is to research the Technical Service Bulletins (TSB) for known issues with the specific vehicle.
Advanced diagnostic steps are highly specific to the vehicle and may require specialized equipment and knowledge for accurate performance. The basic steps provided below should be supplemented with a vehicle-specific repair guide for detailed instructions.
Basic Step #1
Always start by clearing the codes and rescanning the vehicle. If none of the Diagnostic Trouble Codes (DTCs) appear as active immediately, take the vehicle for an extended multi-stop test drive to see if the codes reappear. If only one of the codes is reactivated by the ECM, continue the diagnostic process for that specific code.
Basic Step #2
Inspect the exhaust system for any leaks. Black soot around cracks and gaskets indicates a leak. Address any leaks accordingly, as replacing an exhaust gasket is usually a straightforward task. A properly sealed exhaust system is crucial for the sensors involved in the exhaust system.
Basic Step #3
Use an infrared temperature gun to monitor the temperature of the exhaust before and after the catalytic converter. Compare the results to the manufacturer’s specifications by referring to the specific service manual.
Basic Step #4
If the catalytic converter temperature is within the specified range, focus on the electrical system related to these sensors. Start with the harness and connector of the bank 2 NOx sensor. These harnesses often crack and fail due to the extreme temperatures near the exhaust. Repair any damaged wires by soldering the connections and using heat shrink tubing. Also, inspect the oxygen sensors involved in bank 2 to ensure they are not damaged, as this can affect the downstream NOx readings. Repair any connectors that are not making sufficient connections or not locking properly.
This article is intended for informational purposes only, and the technical data and service bulletins specific to your vehicle should always take precedence.
