Technical Description of OBD-II Trouble Code
The circuit for the position sensor/switch of the exhaust pressure control valve is registering a high signal.
What does that mean?
This diagnostic trouble code (DTC) is a generic code that applies to all OBD-II vehicles with an exhaust pressure control valve sensor or switch. This includes vehicles from VW, Audi, Toyota, and others. The specific repair steps may vary depending on the make and model.
The exhaust pressure control valve (EPC) is a valve controlled by a solenoid. It is used to regulate back pressure during cold temperatures. This helps to increase cabin heat, assist with cold starting, and defrost the windshield.
In most cases, the powertrain control module (PCM) uses information from the exhaust back pressure sensor (EBP), intake air temperature (IAT) sensor, and manifold absolute pressure (MAP) sensor to control the valve. If the PCM detects a problem with the EPC or the IAT, it will disable the ECP. Typically, the ECP is found on diesel engines.
Code P048E is set when the PCM detects a high signal in the exhaust pressure control valve circuit. This usually indicates an open circuit.
What is the severity of this DTC?
This code has a moderate to severe severity level. It is recommended to address this code as soon as possible.
An example of an exhaust pressure control valve:
What are some of the symptoms of the code?
Symptoms of a P048E trouble code may include:
What are some of the common causes of the code?
Possible causes for this code may include:
What are some P048E troubleshooting steps?
Begin by checking the exhaust pressure control valve and its wiring. Look for loose connections, damaged wiring, etc. If any damage is found, repair it as necessary, clear the code, and see if it returns. Next, check for any technical service bulletins (TSBs) related to this issue. If no TSBs are found, you will need to proceed with a step-by-step diagnosis of the system.
The following is a general procedure, as testing for this code can vary between vehicles. To accurately test the system, it is recommended to refer to the manufacturer’s diagnostic flow chart.
Check The Wiring
Before proceeding, consult the factory wiring diagrams to determine the specific wires. Autozone offers free online repair manuals for many vehicles, and ALLDATA offers single vehicle subscriptions.
Test The Solenoid
Disconnect the solenoid connector. Use a digital multimeter set to ohms to measure the internal resistance of the solenoid. To do this, connect the meter between the solenoid B+ terminal and the solenoid ground terminal. Compare the resistance measurement to the factory repair specifications. If the meter displays a reading that is out of specification or out of limits (OL), indicating an open circuit, the solenoid should be replaced.
Check The Power Side Of The Circuit
Ensure that the vehicle has been sitting for at least a few hours (preferably overnight) and is cold. Disconnect the solenoid connector. With the vehicle ignition on, use a digital multimeter set to DC volts to check for power at the solenoid (usually 12 volts). To do this, connect the negative meter lead to ground and the positive meter lead to the solenoid B+ terminal on the harness side of the connector. If voltage is not present, connect the meter set to ohms (with the ignition off) between the B+ terminal on the solenoid connector and the solenoid supply voltage terminal on the PCM. If the meter reads out of limits (OL), there is an open circuit between the PCM and the sensor that will need to be located and repaired. If the meter reads a numeric value, there is continuity.
If everything is functioning properly up to this point, check that there is power coming out of the PCM. To do this, turn the ignition on and set the meter to DC volts. Connect the positive meter lead to the EPC supply voltage terminal on the PCM and the negative lead to ground. If there is no reference voltage from the PCM, the PCM is likely faulty. However, PCMs rarely go bad, so it is recommended to double-check the previous steps.
Check The Ground Portion Of The Circuit
With the vehicle ignition off, use a digital multimeter set to ohms to check for continuity to ground. Disconnect the solenoid connector. Connect the meter between the solenoid ground terminal and chassis ground. If the meter reads a numeric value, there is continuity. If the meter reads out of limits (OL), there is an open circuit between the PCM and the solenoid that will need to be located and repaired.
